mbliner.blogg.se - Airflow icon 15 manual

#Airflow icon 15 manual install#
#Airflow icon 15 manual manual#
#Airflow icon 15 manual full#
#Airflow icon 15 manual code#
#Airflow icon 15 manual Bluetooth#

#Airflow icon 15 manual full#

Where flexible ducting is used ensure it is pulled to 90% of its full length. The fan and ducting should be installed in accordance with the requirements of the Domestic Ventilation Compliance Guide, part of Part F of the Building Regulations. To maximise the air flow, rigid ducting should be used where possible. Individual installation instructions are supplied with each module.Įnsure that flexible duct connections are not over tightened to the spigots. This includes setting the flow rates, fan naming, NICEIC certification and timer module settings.

Follow the simple setup process shown on your screen.

#Airflow icon 15 manual Bluetooth#

Ensure Bluetooth is enabled on your device, then open the app.

#Airflow icon 15 manual install#

Download and install myAirflow from the App Store or Google Play Store to your smart device.To activate the iCONsmart and to set it up: This is normal and will also occur if the fan is in its reset mode. When the iCONsmart is first powered on, you will hear the initial reset for 10-15 seconds. Lightly press front cover onto fan and rotate clockwise. Position front cover over IPX cover in same orientation as it was removed.Refit the IPX screw, checking the IPX cover is secure.Lightly press the IPX cover onto the main body.

6) with the L and R indicator on the IPX cover (Fig.

To replace the IPX cover, line up the L (Left) and R (Right) indicators on the main body of the fan (Fig.

Fit the wall plugs provided or fittings as appropriate for the surface.

Level using guides below the L and R symbols.

Make provision for the electric supply cable and wall plugs / appropriate fittings using the main body as a template.

Mark out and drill a spigot hole to suit 100mm diameter rigid ducting.

Fans should not be fitted to unsupported plasterboards. When fitting fans in the ceiling, if high density plasterboard is not used, a support (min 18mm thick) should be mounted between the ceiling joists. The iCONsmart can be installed into a wall or ceiling.

Using the cable clamp provided, secure the mains cable into place.

Wire the fan to supply cable, referring to the electrical installation guide.

Position the fan so cable entry and fitting holes align with those on the mounting surface.

Pierce the grommet to allow the mains cable to be fed through while maintaining seal integrity.

Fit the sealing grommet supplied into the cable entry hole.

(If you have purchased a module for installation, refer to module instructions now.) These modules are available separately and can be fitted at the time of installation or retro-fitted.

#Airflow icon 15 manual code#

These include: timer module (TM) functionality that can be unlocked via a unique code (on a scratch card), humidity & timer (HT), motion sensor & timer (MST) or a combination of all three (MSHT). 3 month rolling log of power consumption, time on and flow rates recording.Commission / Notify NICEIC of installation.Bluetooth connection to your smart device.ICONsmart has several features included as standard and can also be fitted with digital micro modules to give a range of extra control options. Remove the IPX cover by undoing the screw in the centre.Note front cover position for reassembly purposes. Hold the main body, turn the front cover anticlockwise.Remove locking screw from the bottom of the front cover.Front cover iris leaves must be in the fully closed position.Ensure selected power source being used is isolated.ICONsmart comes with a newly developed flow sensing technology that automatically adjusts and maintains the set extraction flow rates when within the parameters of the fan. Switches for fans should be selected and sited in accordance with BS 7671:2018.

Isolator switch, circuit breaker) with a distance greater than 3 mm between its open contacts shall be required according to BS 60669-1. The iCONsmart 15 is IPX5 rated and therefore it is suitable for mounting in bathrooms (in zone 1 and 2).įor fans mounted in zones 1 & 2 as defined in BS 7671:2018, additional protection must be provided by a Residual Current Device (RCD) not exceeding 30mA as well as having an Arc Fault Detection Device (AFDD).Ī disconnector (e.g. The iCONsmart 15 requires a 110V-240V 50/60 Hz single phase supply. Building Regulations and to the latest IET standards, or the appropriate regulations in the country of installation.

#Airflow icon 15 manual manual#

Airflow iCONsmart 15 - Extractor Fan Manual and Installation VideoĪll electrical installation must be carried out by an approved electrician in accordance with Part "P" U.K.